NSX Health Check Service

[Kaz-kzukNA1]

2. ABS
With standard ABS service at the main dealer, they will only replace the brake fluid inside the ABS reservoir and that’s it. This is better than doing nothing but it won’t replace any fluid at the chamber around the four solenoids for each wheels.

It is recommended to bleed the ABS accumulator and flush the four solenoids at least once in two years time but ideally every year.
So, although ABS system on this NSX was serviced by the main dealer, it was still full of air with dirt inside.



I normally bleed the accumulator twice using fresh fluid. Then, for each solenoids, I’ll activate it in a short burst using the full amount of fresh fluid stored inside the accumulator until there is no more pressure built inside there. Then, before moving onto the next solenoid, I’ll drain out any fluid inside the ABS reservoir in order not to mix any debris from the solenoid and the old fluid. After all four solenoids were flushed, I’ll further bleed the accumulator twice to complete the service.


By this time, the fluid returned to the ABS SST T-wrench would be clear with no air inside the accumulator.

This NSX was very lucky that none of the solenoids were sticky.

Quite often, at least one of them was sticky and either not returning any fluid back to the reservoir or causing slow leak over many hours. There is a technique to cure this problem but in the worst case scenario, you will need to disassemble the ABS solenoid housing or upgrade to the later ABS spec.

I’m hoping to carry out this upgrade on my NSX next year.

[Kaz-kzukNA1]

3. Main Relay
Another common failure parts on our NSX. This one is non-DBW model so it was easy to replace it.


The original one was opened up and re-soldered so that it could be used as an emergency spare for other owners.

Looking at the date stamped on the actual internal relay, it was really old and still using the small spring which was from the old design. There was a tiny hairline crack at the solder joint so I’m glad we replaced it now….


4. Crank Pulley – MT version
On this NSX, the timing belt was replaced in the past but not the Crank Pulley.
Considering the age of this NSX, we decided to replace the pulley as a preventative measure.


Although the pulley bolt was removed during the last timing belt service, it was not cleaned/greased properly so it took quite a lot of torque to loosen it but not too bad compared to other ones.
The original one looked really rusty and tired….
The new one installed with the pulley bolt properly treated and torqued to the spec.
It will be fine for many years.

[Kaz-kzukNA1]

5. Driveshaft – Right side
This is one of the weakest points on our NSX.
Almost all of the NSX will suffer from leaking joints on the driveshaft especially at the right side.

This one was the same and already making noticeable ‘click’ when the wheel was turned by hand.


For most of the NSX, the joint can be separated from the hub/spline with reasonable amount of force. However, on this one, it looked as if it was never removed and heavily corroded that it just didn’t want to come out.

In the end, I had to use the hydraulic hub puller with one big tap to crack open the corrosion. The inner joint was leaking and the outer one was making the ‘click’.

In order to speed up the process, I normally prepare the refurbished one ready for the replacement. During the refurbishment, each joint will be inspected in detail. Then, each roller will be disassembled, cleaned, then lots and lots of pin bearings are packed with new grease to reassemble the roller. With this process, it will provide you with completely different feeling when the joints were turned by hand.

The joints and the shaft were painted in black and using the new boots and grease, the length was set to the spec to adjust the amount of air inside the boot to complete the refurbishment.

Beautiful driveshaft in place.

[Kaz-kzukNA1]

6. Radiator drain bolt O-ring
I was talking with the owner on what happened on Eurostar with the thermal shock recently.

This morning, I noticed small amount of coolant on the garage floor.
Although the tiny amount of leakage from the drain bolt was spotted during the last Health Check Service, it looks like the recent severe cold weather and rise of temperature this morning speeded up the leakage.

I’ll be replacing the two O-rings next week…


I’ll be servicing the front rackend/tierod area before going to the alignment place in the new year and at the same time, I'll be looking into the door window alignment if I have enough time.

It’s going to be busy for next few weeks to carry out several Health Check for other owners while finishing this NSX….


Regards,
Kaz

[anachonda]

Thank Kaz for your help, i found lot of informations for my NSX.

[AR]

Thanks for the explanation on the stainless parts Kaz, thw cutting bolts and nuts bits makes a lot of sense.