Sorry Kaz, I can't work out how to upload the photo.
The bush I refer to is the white one just to the left of the EO sticker, in the upper of the two slots. On your photo is has no rod inserted in it.
It is the one with the threaded rod.
Regards,
Andy
Platinum Member
the one beside the EO sticker and the one with the yellow bit are the same bush, just the other way around...
if you look on the parts diagram/list you posted, note that 2 are required per door....
here's the (usually overpriced) Lings page....
https://www.lingshondaparts.com/part...ckref/B__5310/
Last edited by britlude; 09-06-2020 at 08:30 PM.
aka Jonathan!!
'92 charlotte green auto.... as a daily
'37 Ford Y street rod......... something for the weekend!
...... if a photobucket pic is foggy, click it, and it'll take you to the clear version, yes, it's a clicking faff....
OK, Thanks to both Jonathan and Kaz, that will explain why it isn't really lined up with either of the rods in the diagram, it fits both.
I shall be on to Honda in the morning to attempt to purchase the required part.
Regards,
Andy
Platinum Member
On purposely used that photo in my previous post as I didn't want showing how a certain parts installed for the security system at the driver side door.
The fastener in the lower slot is not complete and missing the silver washer.
Also, on the later model or different country spec, the area around the lower slot will look completely different so please only refer the photo for the upper slot where the rear sash rod is connected.
Took extra photo so hope these will help.
You may struggle placing the 04721- in the upper slot.
It's quite obvious but just sandwich the brass coloured metal slot on the door lock assy where the green arrows indicate.
Kaz
Honda's computer has been taken over by a Ransomware and no show room and parts department are able to use their computer to look up anything..happening in UK, Germany and Japan? all over the world?
https://www.bbc.co.uk/news/technology-52982427
So you may find it difficult to look up or get parts.
SS
Lexus LC500h.......New Daily run around with some saving the Planet thoughts
Black/black 95 NSX NA with mk1 Ary exhaust....Now sold
Red/Black 91 NSX treasure.....FINo more NA
Silver/Pearl White/Black 1993 NSX 3.0 5 MT NSX ZAZ R-GT Twin Scroll Turbo
A late question for Midnight Blue. I presume that by now you have installed 04721 and buttoned everything back up. Hopefully successfully. If so, I am about to go through this procedure when 04721 arrives from Amayama in Japan (Acura Canada has none in stock) and I was curious as to whether you managed to get the yellow bush and metal washer on the retainer with the latch still mounted in the door? The part has not arrived yet; but, I have been looking inside the door and I am thinking that this is not going to happen in situ unless I can get the doctor next door to sneak the critical parts of a laparoscopic surgical ensemble out of the hospital to do the work. I am thinking that it might be possible to remove the latch bolts so that I can reposition the latch so that I can apply the yellow bush and metal washer through the large slot where the strike enters the door latch. Other wise I have to remove the outside window trim so I can remove the rear sash and the rear window guide which provides the necessary room to extract the latch mechanism.
Please tell me that there is a less painful way to do this!
Hi,Originally Posted by Old guy
I can't quite remember how I got it all to fit in the end but it did involve bad language and skinned knuckles. The rod that comes from the handle to 04721 was not correctly aligned. I did have to loosen the door latch if not take the bolts out completely. I certainly didn't have to remove the rear sash. With the latch not rigidly fastened in place I could get 04721 in place and get the whole assembly aligned with the door rod correctly so it would pop through into place.
Posting Permissions
Reply With Quote
