View RSS Feed

Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer

Updates from Kaz-kzukNA1

  1. Advan Neova AD-08, Compliance Pivot, without ABS

    by , 16-02-2011 at 10:59 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)

    I have now covered about 4k miles on Advan Neova AD-08.



    I’m using OEM 16/17in wheels so the tyre size is 215/45/16 and 245/40/17.



    I have Type-S suspension and I use my own alignment setup so following comment may not be the case for you especially if you are using wider tyres.


    OEM tyre width is somehow quite narrow considering the characteristic and the spec of our NSX.


    Long time ago, I was ...
    Tags: ad 08, neova Add / Edit Tags
    Categories
    Uncategorized
  2. ABS Error code #13 (and #14) Part 3 ...

    by , 16-02-2011 at 10:46 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)
    Well, well… Surprise, surprise…


    Recently, my FL wheel speed sensor failed with open circuit and triggered the ABS Error code #13.


    I placed an order for the replacement.


    It was on back order with estimated 3 weeks lead time…


    Yesterday, I had to drive long miles for a meeting and the NSX was parked on the street in the rain.


    After the meeting, started the engine and the ABS warning ...
    Tags: abs #13, abs #14 Add / Edit Tags
    Categories
    Uncategorized
  3. Too tight... Drive shaft 02

    by , 16-02-2011 at 10:24 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)
    Click image for larger version. 

Name:	HubPuller.JPG 
Views:	1023 
Size:	175.5 KB 
ID:	8599


    After spending hours, finally, managed to move R & L drive shaft spline from the hub.


    I had to apply so much pressure using the hydraulic puller that I thought I would break the tool.


    I used this puller so many times but never had to apply this amount of force in the past.


    As I need to have maximum space especially on the left drive shaft to pop out the inboard joint, I’m ...
    Tags: drive shaft Add / Edit Tags
    Categories
    Uncategorized
  4. A/C Climate Control Unit (CCU) 03, Cabin Temperature Sensor

    by , 16-02-2011 at 10:14 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)

    Click image for larger version. 

Name:	C24After.JPG 
Views:	5215 
Size:	163.6 KB 
ID:	8596

    After checking the circuit, it’s time to install the new capacitors.


    After cleaning the board one more time and carried out the inspection, applied the conformal coating to the board.


    At the same time, re-soldered two Main Relays (for another owner) and coated them as well.



    Click image for larger version. 

Name:	Coating.JPG 
Views:	5032 
Size:	246.4 KB 
ID:	8597



    Click image for larger version. 

Name:	CabinTempBefore.JPG 
Views:	5161 
Size:	167.4 KB 
ID:	8595

    ...

    Updated 07-04-2011 at 11:26 AM by Kaz-kzukNA1

    Categories
    Uncategorized
  5. A/C Climate Control Unit (CCU) 02

    by , 15-02-2011 at 11:45 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)
    As I need to be in another meeting this afternoon, decided to work on the CCU for a while.


    Although there were lots of capacitor leakages, considering the actual age of the board, the damage level was better than other boards that I serviced in the past.


    Click image for larger version. 

Name:	C24Bridged.JPG 
Views:	1326 
Size:	167.9 KB 
ID:	8590Click image for larger version. 

Name:	C24Removed.JPG 
Views:	1304 
Size:	194.6 KB 
ID:	8593


    Click image for larger version. 

Name:	C14Bridged.JPG 
Views:	1208 
Size:	199.5 KB 
ID:	8591Click image for larger version. 

Name:	C14Removed.JPG 
Views:	1312 
Size:	179.5 KB 
ID:	8592


    Some of the leaked capacitors removed, cleaned
    ...

    Updated 07-04-2011 at 11:25 AM by Kaz-kzukNA1

    Categories
    Uncategorized