View RSS Feed

Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer

Updates from Kaz-kzukNA1

  1. Kaz-kzukNA1's Avatar

    Eng Refresh 18

    by
    Kaz-kzukNA1
    , 17-01-2014 at 01:33 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)






    New gasket for the VVIS chamber and butterfly mechanism.




    Must replace all ten washers.



     ...
    Categories
    Eng Refresh Stage 1 + LMA
    Comments 0 Comments
    Read MoreRead More
  2. Kaz-kzukNA1's Avatar

    Eng Refresh Stage 2 – 19

    by
    Kaz-kzukNA1
    , 28-01-2012 at 10:17 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)






    Installed new gaskets and seals on the painted valve cover.
    The inside of the cover is very clean after being washed.




    ...

    Updated 01-06-2012 at 11:06 PM by Kaz-kzukNA1

    Categories
    Engine Refresh Stage 2
    Comments 0 Comments
    Read MoreRead More
  3. Kaz-kzukNA1's Avatar

    TB/WP/Valve 11

    by
    Kaz-kzukNA1
    , 20-06-2011 at 10:40 PM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)




    Click image for larger version.  Name: VeryDirtyValveCover.JPG  Views: 1319  Size: 193.9 KB  ID: 9661
    Click image for larger version.  Name: InstalledNewGasketValveCover.JPG  Views: 1334  Size: 176.8 KB  ID: 9659

    So, something looked like this is now cleaned to this level and valve cover gaskets as well as the spark plug seals are replaced with the new ones.




    Click image for larger version.  Name: InstalledNewGasketTBlowerCoverIGNcoilCover.JPG  Views: 1376  Size: 171.0 KB  ID: 9658

    Installed the new gasket on the new TB Lower cover.
    And one of the most important gaskets replaced on the IGN coil covers.




    Click image for larger version.  Name: InstalledNewGasketMidCover.JPG  Views: 1325  Size: 162.8 KB  ID: 9660
    ...
    Categories
    TB/WP/Valve Service , Engine/Tyre
    Comments 0 Comments
    Read MoreRead More
  4. Kaz-kzukNA1's Avatar

    TB/WP/Valve 08

    by
    Kaz-kzukNA1
    , 06-05-2011 at 06:32 AM (Today at Atelier Kaz - ex-Honda R&D, F1, Indy/CART engineer)


    Before going any further, wanted to carry out the vacuum leak check of the cooling system especially after replacing the WP as well as all of the coolant hoses.


    You don’t want to find any leakage at the WP after re-assembling everything as you will need to remove almost everything again to get to the WP.


    Click image for larger version.  Name: VacuumLeakCheck.JPG  Views: 1665  Size: 160.9 KB  ID: 9219
    Click image for larger version.  Name: OilCoolerHoses.JPG  Views: 1624  Size: 160.6 KB  ID: 9217

    Installed the header tank and oil cooler hoses in ...
    Categories
    TB/WP/Valve Service , Engine/Tyre , Cooling
    Comments 0 Comments
    Read MoreRead More